Electronic Fuel Injection
From John Clarke Mills Project Wiki
m |
|||
| Line 5: | Line 5: | ||
[[TWMComponenets| TWM 40mm throttle bodies, TPS, fuel rail, and regulator]] | [[TWMComponenets| TWM 40mm throttle bodies, TPS, fuel rail, and regulator]] | ||
<br/> | <br/> | ||
| - | [[ | + | [[Fuel_Plumbing_For_Electronic_Fuel_Injection| Fuel plumbing]] |
==Research== | ==Research== | ||
| Line 42: | Line 42: | ||
* Injectors (22# Bosch Pink Tops) | * Injectors (22# Bosch Pink Tops) | ||
* Lokar throttle cable 36" | * Lokar throttle cable 36" | ||
| - | * [[ | + | * [[Fuel_Plumbing_For_Electronic_Fuel_Injection| Fuel plumbing, filters, AN fittings, etc]] |
* Mangoletsi barb for brake vacuum | * Mangoletsi barb for brake vacuum | ||
* Grommets | * Grommets | ||
* More band clamps (big ones for fuel pump) | * More band clamps (big ones for fuel pump) | ||
* Hose mounting clamps | * Hose mounting clamps | ||
| + | * 50mm TWM air horns | ||
| - | |||
* 470 ohm resistor (in between MS and O2 sensor)? | * 470 ohm resistor (in between MS and O2 sensor)? | ||
| - | |||
| - | |||
==Notes to self== | ==Notes to self== | ||
| - | + | (none at this time) | |
Revision as of 04:09, 1 November 2006
Contents |
Building
Calibrating temperature sensors
TWM 40mm throttle bodies, TPS, fuel rail, and regulator
Fuel plumbing
Research
Initial thoughts: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319629
FIdle and MAP: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319717
Fuel plumbing, etc: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,204528/
MegaSquirt and Crane XR700: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,275308/
Thermistor sensors: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,324206/highlight,/#324206
Throttle linkage: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,280025/
AN Fittings: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,280238/
Master parts list
- 2 TWM 2900 DOCE 40mm's (2900 + 2910)
- TWM Fuel rail
- TWM pressure regulator (2800-6401)
- TWM TPS switch and plug
- Mangoletsi intake manifold
- 318 water manifold
- Copper pipe bypassing manifold (to heater box)
- Electronic under-car fuel pump (40+ PSI. for a Ford F150)
- MegaSquirt (MS II v3. keeping distributor for now, future expansion in mind)
- O2 sensor (Innovate LC-1)
- 12' MegaSquirt pre-labeled wiring harness
- Mechanical fuel pump blockoff plate
- Two Bosch temperature sensors (62110788115)
- Painless wiring 7 circuit fuse box (dual relay hot switched relays)
- OEM BMW intake manifold gaskets
- Injectors (22# Bosch Pink Tops)
- Lokar throttle cable 36"
- Fuel plumbing, filters, AN fittings, etc
- Mangoletsi barb for brake vacuum
- Grommets
- More band clamps (big ones for fuel pump)
- Hose mounting clamps
- 50mm TWM air horns
- 470 ohm resistor (in between MS and O2 sensor)?
Notes to self
(none at this time)
