Electronic Fuel Injection
From John Clarke Mills Project Wiki
Line 43: | Line 43: | ||
* Injectors (22# Bosch Pink Tops) | * Injectors (22# Bosch Pink Tops) | ||
* Lokar throttle cable 36" | * Lokar throttle cable 36" | ||
- | * Fuel plumbing, filters, AN fittings, etc | + | * [[FuelPlumbingForEFI| Fuel plumbing, filters, AN fittings, etc]] |
* Mangoletsi barb for brake vacuum | * Mangoletsi barb for brake vacuum | ||
- | |||
- | |||
* Grommets | * Grommets | ||
* More band clamps (big ones for fuel pump) | * More band clamps (big ones for fuel pump) | ||
+ | |||
+ | * 470 ohm resistor (in between MS and O2 sensor)? | ||
* A way to clamp fuel filters to firewall | * A way to clamp fuel filters to firewall | ||
- | |||
* Heat shrink | * Heat shrink | ||
- | * | + | * Barb for MAP collector |
- | + | * Hose for MAP to ECU | |
- | + | * Wire terminators to terminal (2 AWG to 3/8) | |
- | + | * Steel or copper pipe for MAP collector and caps | |
- | * | + | |
- | * | + | |
- | * | + | |
- | + | ||
==Notes to self== | ==Notes to self== | ||
*Find out about fitting them together. Any tape, gel, or lubricant of some sort? | *Find out about fitting them together. Any tape, gel, or lubricant of some sort? | ||
- | * | + | *Ask about mounting fuel filter in engine bay |
- | + | ||
- | + | ||
*Paint brake booster | *Paint brake booster | ||
+ | *Bring MS ECU to kragen/hardware and get barb. Also get hose for it | ||
+ | |||
Electric fan: http://www.msefi.com/viewtopic.php?p=125133 | Electric fan: http://www.msefi.com/viewtopic.php?p=125133 |
Revision as of 02:31, 22 October 2006
Contents |
Building
Calibrating temperature sensors
TWM 40mm throttle bodies, TPS, fuel rail, and regulator
Fuel plumbing
Research
Initial thoughts: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319629
FIdle and MAP: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319717
Fuel plumbing, etc: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,204528/
MegaSquirt and Crane XR700: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,275308/
Thermistor sensors: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,324206/highlight,/#324206
Throttle linkage: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,280025/
AN Fittings: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,280238/
Master parts list
- 2 TWM 2900 DOCE 40mm's (2900 + 2910)
- TWM Fuel rail
- TWM pressure regulator (2800-6401)
- TWM TPS switch and plug
- Mangoletsi intake manifold
- 318 water manifold
- Copper pipe bypassing manifold (to heater box)
- Electronic under-car fuel pump (40+ PSI. for a Ford F150)
- MegaSquirt (MS II v3. keeping distributor for now, future expansion in mind)
- O2 sensor (Innovate LC-1)
- 12' MegaSquirt pre-labeled wiring harness
- Mechanical fuel pump blockoff plate
- Two Bosch temperature sensors (62110788115)
- Painless wiring 7 circuit fuse box (dual relay hot switched relays)
- OEM BMW intake manifold gaskets
- Injectors (22# Bosch Pink Tops)
- Lokar throttle cable 36"
- Fuel plumbing, filters, AN fittings, etc
- Mangoletsi barb for brake vacuum
- Grommets
- More band clamps (big ones for fuel pump)
- 470 ohm resistor (in between MS and O2 sensor)?
- A way to clamp fuel filters to firewall
- Heat shrink
- Barb for MAP collector
- Hose for MAP to ECU
- Wire terminators to terminal (2 AWG to 3/8)
- Steel or copper pipe for MAP collector and caps
Notes to self
- Find out about fitting them together. Any tape, gel, or lubricant of some sort?
- Ask about mounting fuel filter in engine bay
- Paint brake booster
- Bring MS ECU to kragen/hardware and get barb. Also get hose for it
Electric fan: http://www.msefi.com/viewtopic.php?p=125133