Electronic Fuel Injection

From John Clarke Mills Project Wiki

Revision as of 06:51, 20 October 2006 (edit) Millsj (Talk | contribs) ← Previous diff		Revision as of 19:35, 20 October 2006 (edit) (undo) Millsj (Talk | contribs) Next diff →
Line 52:		Line 52:
	* Lots of wire		* Lots of wire
	* Heat shrink		* Heat shrink
		+	* Fuel filter in between tank and fuel pump
	==Tools still needed==		==Tools still needed==

---

Revision as of 19:35, 20 October 2006

Contents 1 Building 2 Research 3 Master parts list 4 Tools still needed 5 Notes to self

Building

Calibrating temperature sensors
TWM 40mm throttle bodies, TPS, fuel rail, and regulator
Fuel plumbing

Research

Initial thoughts: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319629
FIdle and MAP: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319717
Fuel plumbing, etc: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,204528/
MegaSquirt and Crane XR700: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,275308/
Thermistor sensors: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,324206/highlight,/#324206
Throttle linkage: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,280025/
AN Fittings: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,280238/

Master parts list

• 2 TWM 2900 DOCE 40mm's (2900 + 2910)
• TWM Fuel rail
• TWM pressure regulator (2800-6401)
• TWM TPS switch and plug
• Mangoletsi intake manifold
• 318 water manifold
• Copper pipe bypassing manifold (to heater box)
• Electronic under-car fuel pump (40+ PSI. for a Ford F150)
• MegaSquirt (MS II v3. keeping distributor for now, future expansion in mind)
• O2 sensor (Innovate LC-1)
• 12' MegaSquirt pre-labeled wiring harness
• Mechanical fuel pump blockoff plate
• Two Bosch temperature sensors (62110788115)
• Painless wiring 7 circuit fuse box (dual relay hot switched relays)
• OEM BMW intake manifold gaskets
• Injectors (22# Bosch Pink Tops)
• Lokar throttle cable 36"
• Fuel plumbing, filters, AN fittings, etc
• Mangoletsi barb for brake vacuum

• 470 ohm resistor (in between MS and O2 sensor)
• Grommets
• More band clamps (big ones for fuel pump)
• A way to clamp fuel filters to firewall
• Lots of wire
• Heat shrink
• Fuel filter in between tank and fuel pump

Tools still needed

• File/rasp
• Longer 3/8" and 1/4" socket extensions
• Universal joint - 3/8" socket
• Silicone gasket maker

Notes to self

• Find out about fitting them together. Any tape, gel, or lubricant of some sort?
• Go to car and get fuel line to measure then order AN6 to return line
• Clean trunk and bring stuff inside
• Try and fit fuel pump with band clamps

Electric fan: http://www.msefi.com/viewtopic.php?p=125133