Electronic Fuel Injection
From John Clarke Mills Project Wiki
m (→Master parts list) |
|||
Line 47: | Line 47: | ||
* Grommets | * Grommets | ||
* More band clamps (big ones for fuel pump) | * More band clamps (big ones for fuel pump) | ||
+ | * Hose mounting clamps | ||
* 470 ohm resistor (in between MS and O2 sensor)? | * 470 ohm resistor (in between MS and O2 sensor)? | ||
- | |||
* Heat shrink | * Heat shrink | ||
* Barb for MAP collector | * Barb for MAP collector |
Revision as of 19:54, 22 October 2006
Contents |
Building
Calibrating temperature sensors
TWM 40mm throttle bodies, TPS, fuel rail, and regulator
Fuel plumbing
Research
Initial thoughts: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319629
FIdle and MAP: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319717
Fuel plumbing, etc: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,204528/
MegaSquirt and Crane XR700: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,275308/
Thermistor sensors: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,324206/highlight,/#324206
Throttle linkage: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,280025/
AN Fittings: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,280238/
Master parts list
- 2 TWM 2900 DOCE 40mm's (2900 + 2910)
- TWM Fuel rail
- TWM pressure regulator (2800-6401)
- TWM TPS switch and plug
- Mangoletsi intake manifold
- 318 water manifold
- Copper pipe bypassing manifold (to heater box)
- Electronic under-car fuel pump (40+ PSI. for a Ford F150)
- MegaSquirt (MS II v3. keeping distributor for now, future expansion in mind)
- O2 sensor (Innovate LC-1)
- 12' MegaSquirt pre-labeled wiring harness
- Mechanical fuel pump blockoff plate
- Two Bosch temperature sensors (62110788115)
- Painless wiring 7 circuit fuse box (dual relay hot switched relays)
- OEM BMW intake manifold gaskets
- Injectors (22# Bosch Pink Tops)
- Lokar throttle cable 36"
- Fuel plumbing, filters, AN fittings, etc
- Mangoletsi barb for brake vacuum
- Grommets
- More band clamps (big ones for fuel pump)
- Hose mounting clamps
- 470 ohm resistor (in between MS and O2 sensor)?
- Heat shrink
- Barb for MAP collector
- Hose for MAP to ECU
- Wire terminators to terminal (2 AWG to 3/8)
- Steel or copper pipe for MAP collector and caps
Notes to self
- Find out about fitting them together. Any tape, gel, or lubricant of some sort?
- Ask about mounting fuel filter in engine bay
- Paint brake booster
- Bring MS ECU to kragen/hardware and get barb. Also get hose for it
- Check for coolant plumbing pieces in car
Electric fan: http://www.msefi.com/viewtopic.php?p=125133