Electronic Fuel Injection
From John Clarke Mills Project Wiki
m |
|||
Line 1: | Line 1: | ||
- | + | ==To Do== | |
+ | |||
+ | *Run fuel plumbing | ||
+ | *Mount fuel pump | ||
+ | *Run power to it | ||
+ | *Throttle linkage | ||
+ | |||
+ | |||
+ | ==Building== | ||
[[ThermistorCalibration| Calibrating temperature sensors]] | [[ThermistorCalibration| Calibrating temperature sensors]] | ||
Line 8: | Line 16: | ||
- | + | ==Research== | |
Initial thoughts: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319629 | Initial thoughts: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319629 | ||
Line 23: | Line 31: | ||
- | + | ==Master parts list== | |
* 2 TWM 2900 DOCE 40mm's (2900 + 2910) | * 2 TWM 2900 DOCE 40mm's (2900 + 2910) | ||
Line 51: | Line 59: | ||
- | + | ==Tools still needed== | |
* File/rasp | * File/rasp | ||
Line 59: | Line 67: | ||
- | + | ==Later additions== | |
Electric fan: http://www.msefi.com/viewtopic.php?p=125133 | Electric fan: http://www.msefi.com/viewtopic.php?p=125133 |
Revision as of 04:49, 7 September 2006
Contents |
To Do
- Run fuel plumbing
- Mount fuel pump
- Run power to it
- Throttle linkage
Building
Calibrating temperature sensors
TWM 40mm throttle bodies, TPS, fuel rail, and regulator
Fuel plumbing
Research
Initial thoughts: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319629
FIdle and MAP: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,319717
Megasquirt: http://msefi.com/viewtopic.php?t=19369
Fuel plumbing, etc: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,204528/
MegaSquirt and Crane XR700: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/t,275308/
Thermistor sensors: http://www.bmw2002faq.com/component/option,com_forum/Itemid,57/page,viewtopic/p,324206/highlight,/#324206
Master parts list
- 2 TWM 2900 DOCE 40mm's (2900 + 2910)
- TWM Fuel rail
- TWM pressure regulator (2800-6401)
- TWM TPS switch and plug
- Mangoletsi intake manifold
- 318 water manifold
- Copper pipe bypassing manifold (to heater box)
- Electronic under-car fuel pump (40+ PSI. for a Ford F150)
- MegaSquirt (MS II v3. keeping distributor for now, future expansion in mind)
- O2 sensor (Innovate LC-1)
- 12' MegaSquirt pre-labeled wiring harness
- Mechanical fuel pump blockoff plate
- Two Bosch temperature sensors (62110788115)
- Painless wiring 7 circuit fuse box (dual relay hot switched relays)
- OEM BMW intake manifold gaskets
- Injectors (20 pound high impedence)
- 470 ohm resistor (in between MS and O2 sensor)
- Lokar throttle cable 36"
- Mangoletsi barb for brake vacuum
- Two fuel filters
- Braided steel fuel lines
- Grommets
- More band clamps
Tools still needed
- File/rasp
- Longer 3/8" and 1/4" socket extensions
- Universal joint - 3/8" socket
- Silicone gasket maker
Later additions
Electric fan: http://www.msefi.com/viewtopic.php?p=125133